Toughness and Fracture Surface of Frame of Drone Based on Composite from Waste Materials
DOI:
https://doi.org/10.21063/jtm.2019.v9.i2.52-58Kata Kunci:
green composite, waste material, quadcopter, toughness, fracture surfaceAbstrak
Application of green composites material is aerial egineering. Advantages of green composites material are lightweight and relatively strong. This reason that makes green composites can be applied in Unmanned Aerial Vehicle (UAV). In this study, material of quadcopter frame was composites material that made of waste material from styrofoam, bagasse and eggshell. Styrofoam was used as binder of composite material. Bagasse and eggshell were used as reinforcement in green composite material. The investigation focused on effect of volume fraction on flying time of quadcopter that made of green composites material. This study showed that addition of eggshell powder in composites up 25% by volume fraction, result in decreasing the flying time of quadcopter. Addition of eggshell powder in composites up 25% by volume fraction, result in decreasing the porous of green composite. Porous structure affect the flying time of quadcopter based on green composite materials that made of waste material from styrofoam, bagasse and eggshell. Green composite based on styrofoam, bagasse and eggshell can be applied in Unmanned Aerial Vehicle (UAV) materials.
Referensi
J. Holbery and D. Houston, “Natural-fibre-reinforced polymer composites in automotive applications,” Jom, vol. 58, no. 11, pp. 80–86, 2006.
M. R. Sanjay, G. R. Arpitha, L. L. Naik, K. Gopalakrishna, and B. Yogesha, “Applications of Natural Fibers and Its Composites : An Overview,” J. Nat. Resour., vol. 7, pp. 108–114, 2016.
M. Perdana, Prastiawan, and S. Hadi, “IOP Conference Series : Earth and Environmental Science Mechanical Properties of Composite Waste Material Based Styrofoam , Baggase and Eggshell Powder for Application of Drone Frames Mechanical Properties of Composite Waste Material Based Styrofoam , Bag,” in IOP Conf. Series: Earth and Environmental Science 97 (2017) 012034, 2017, pp. 1–7.
K. L. Pickering, M. G. A. Efendy, and T. M. Le, “A review of recent developments in natural fibre composites and their mechanical performance,” Compos. Part A Appl. Sci. Manuf., vol. 83, pp. 98–112, 2016.
D. N. Saheb and J. P. Jog, “Natural Fiber Polymer Composites : A Review,” J. Adv. Polym. Technol., vol. 18, no. 4, pp. 351–363, 2015.
U. S. Bongarde and V. . . Shinde, “Review on natural fiber reinforcement polymer composites,” Int. J. Eng. Sci. Innov. Technol., vol. 3, no. 2, pp. 431–436, 2014.
S. da L. Maria, S. da C. Maria, A. G. Roberto, A. Pascoal, and S. da C. Aparecida, “Polypropylene Composites Reinforced with Biodegraded Sugarcane Bagasse Fibers : Static and Dynamic Mechanical Properties,” Mater. Res., vol. 19, no. 1, pp. 75–83, 2015.
S. L. Suban and M. Farid, “Pengaruh Panjang Serat terhadap Nilai Koefisien Absorpsi Suara dan Sifat Mekanik Komposit Serat Ampas Tebu dengan Matriks,” J. Tek. ITS, vol. 4, no. 1, pp. 101–105, 2015.
I. O. Oladele, “Effect of Bagasse Fibre Reinforcement on the Mechanical Properties of Polyester Composites,” J. Assoc. Prof. Eng. Trinidad Tobago, vol. 42, no. 1, pp. 12–15, 2014.
A. S. Yusuff, O. D. Adeniyi, M. A. Olutoye, and U. G. Akpan, “Development and Characterization of A Composite Anthill-Chiken Eggshell Catalyst For Biodiesel Production From Waste Frying Oil,” Int. J. Technol., vol. 9, no. 1, pp. 110–119, 2018.
M. Perdana and R. P. Yulsardi, “Pengaruh Fraksi Volume Penguat Terhadap Kekuatan Lentur Green Composite Untuk Aplikasi Pada Bodi Kendaraan,” J. Iptek Ter. Kopertis Wil. X, vol. 3, pp. 71–77, 2015.
M. Müller, “Mechanical Properties of Composite Material Reinforced with Textile Waste from the Process of Tyres Recycling,” Int. J. Res. Agric. Eng., vol. 62, no. 2015, pp. 99–105, 2016.
X. Zhang and Y. Han, “Thermal Insulation Properties of Fly Ash and Waste Polystyrene Mixed Block Building Materials,” Chem. Eng. Trans. J., vol. 55, pp. 253–258, 2016.
H. Ghasemnejad, Y. Argentiero, T. A. Tez, and P. E. Barrington, “Impact damage response of natural stitched single lap-joint in composite structures,” Mater. Des., vol. 51, pp. 552–560, 2013.
H. Mamtaz, M. H. Fouladi, M. Al-atabi, and S. N. Namasivayam, “Acoustic Absorption of Natural Fiber Composites,” J. Eng., vol. 2016, pp. 1–11, 2016.
J. Romdhoni, Muhammad Fajri, Adiyanto and H. W. Sedoputro, “Penggunaan Drone sebagai Media Digitasi Penggambaran 3 Dimensi Bangunan dan Pemetaan Kawasan,” in Prosiding Temu Ilmiah IPLBI 2016, 2016, no. 1, pp. 149–154.
A. Balachandran, D. Karelia, and J. Challa, “Material Selection for Unmanned Aerial Vehicle,” Int. J. Mech. Enginering Technol., vol. 5, no. 8, pp. 34–40, 2014.
A. Sajjad, K. Anjum, R. A. Sufian, Z. Abbas, and I. M. Qureshi, “Attitude Control of Quadcopter Using Adaptive Neuro Fuzzy Control,” Int. J. Hybrid Inf. Technol., vol. 9, no. 4, pp. 139–150, 2016.
S. Ragavendhiran, S. Sathishkumar, C. Yogeswaran, and S. Palanisamy, “Wireless Control Quadcopter with Self- Balancing System,” Int. J. Innov. Res. Sci. Eng. Technol., vol. 4, no. 6, pp. 523–529, 2015.
N. Ives, R. Pacheco, D. De Castro, R. Resende, and A. A. Magalhães, “Stability Control of an Autonomous Quadcopter through PID Control Law,” Int. J. Eng. Res. Appl., vol. 5, no. 5, pp. 7–10, 2015.
A. A. Abdullah, S. Shahib, and N. A. Abu, “Drone Ad-Hoc Networks ( DRANETs ),” in Annual South East Asian International Seminar (ASAIS) 2017, 2017, pp. 113–124.
L. Iryani, A. M. Kadir, and B. Irawan, “Design and Analysis of Spar I Beam Profile Using Composite Material in UAV Structure,” in Annual South East Asian International Seminar (ASAIS) 2017, 2017, pp. 45–50.
J. Chaishome and S. Supapvanich, “Polylactic Acid (PLA) based Green Coposites Reinforced Pineapple Leaf Fibres : Evaluation of Processing and Tensile Performance,” in ICEAST 2018, 2018, vol. 192, pp. 1–4.
S. Ashworth, J. Rongong, P. Wilson, and J. Meredith, “Mechanical and Damping Properties of Resin Transfer Moulded Jute-Carbon Hybrid Composites,” Compos. Part B Eng., vol. 105, pp. 60–66, 2016.
G. Zhang, O. R. Ghita, and K. E. Evans, “Dynamic Thermo-Mechanical and Impact Properties of Helical Auxetic Yarns,” Compos. Part B Eng., vol. 99, pp. 494–505, 2016.
Unduhan
Diterbitkan
Terbitan
Bagian
Lisensi
Hak Cipta (c) 2019 M. Perdana
Artikel ini berlisensiCreative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
