Failure Analysis of Induced Draft Fan Bearing in PT Semen Padang Using The RCM Method

Authors

  • Rozi Saferi Institut Teknologi Padang
  • Sulaeman Institut Teknologi Padang
  • Olka Defra Wanda Institut Teknologi Padang

DOI:

https://doi.org/10.21063/jtm.2023.v13.i1.19-26

Keywords:

Induced Draft Fan, Bearing, FMECA, RCM

Abstract

The development of the technology is getting trigger competition in industri. To compete, companies should can provide products and the quality of services best for consumer. This study aims to find out the causes of bearings that are damaged in the Induced Draft Fan (IDF Bearing) and how to plan strategic maintenance of IDF Bearing. The method used is reliability centered maintenance (RCM). The causes of bearing damage are analyzed using the Failure Mode Effect and Critical Analysis (FMECA) method. The results of this study show that the cause of IDF Bearing damage is clearance with an RPN value of 210, lubrication system with an RPN value of 36, unbalance with an RPN value of 72, and high temperature with an RPN value of 54. Scheduled Restoration Maintenance is applied for IDF Bearing , where task or preventive maintenance in the form of oil change with a time of 5803.2 hours or 241 days.

References

M. Asdar (2020), “Penerapan Preliminary Hazard Analysis dan Fault Tree Analysis untuk Mengidentifikasi Bahaya Kerusakan dan Penyebab Kegagalan Mesin Crusher di PT. Prima Karya Manunggal,” Politeknik ATI Makassar, pp. 1–60.

F.H. Akbar, T.I Oesman & E.W. Asih (2017), “Analisis Kegagalan Turbine Guide Bearing Menggunakan Metode Reliability Centered Maintenance (RCM),” Jurnal Rekavasi, Vol. 5, No.1, pp. 25-31.

K,S. Sularso (2004), “Dasar Perancanaan dan Pemilihan Elemen Mesin,” In PT. AKA (Ed.), 11, (p.352), Pradnya Paramita, Jakarta Pitoyo.

A.N. Bintoro 2019, “Analisis Penyebab Kerusakan Bearing pada Shaft Generator di MV. Armada Papua , Doctoral Dissertation, Politeknik Ilmu Pelayaran, Semarang.

J. Moubray (1997), “Reliability Centered Maintenance-RCM II,” Second Edition, Industrial Press Inc., New York.

D. Dermawan & F.A Yul (2016), “Penerapan Reliability Centered Maintenance pada Motor Hoist Tower Crane,” Simposium Nasional Teknologi Terapan (SNIT) 4, ISSN:2339-028X. Universitas Muhammadiyah

Z. Sajaradj, L.N. Huda & S. Sinulingga (2023), “The Application of Reliability Centered Maintenance (RCM) Methods to Design Maintenance System in Manufacturing (Journal Review) ,” 1st International Conference on Industrial and Manufacturing EngineeringIOP Conf. Series: Materials Science and Engineering 505 (2019) 012058, doi:10.1088/1757-899X/505/1/012058

I.H. Hasan, Denur & L. Hakim (2019), “Penerapan Reliability Centered Maintenance (RCM) pada Mesin Ripple Mill,” SURYA TEKNIKA, Vol. 6, No. 1, pp. 43–48.

Downloads

Published

2023-04-30

How to Cite

Saferi, R., Sulaeman, & Defra Wanda, O. (2023). Failure Analysis of Induced Draft Fan Bearing in PT Semen Padang Using The RCM Method. Jurnal Teknik Mesin, 13(1), 19–26. https://doi.org/10.21063/jtm.2023.v13.i1.19-26

Issue

Vol. 13 No. 1 (2023): Jurnal Teknik Mesin Vol.13 No.1 April 2023

Section

Article

License

Copyright (c) 2023 Rozi Saferi, Sulaeman, Olka Defra Wanda

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.