Flying Time Of Quadcopter Based On Green Composites Material

Authors

  • Mastariyanto Perdana Institut Teknologi Padang
  • Nurzal Institut Teknologi Padang
  • Syahrul Firdaus Institut Teknologi Padang
  • Rozi Saferi Institut Teknologi Padang

DOI:

https://doi.org/10.21063/jtm.2018.v8.i2.73-77

Keywords:

green composite, waste material, quadcopter, flying time, styrofoam

Abstract

Application of green composites material is aerial egineering. Advantages of green composites material are lightweight and relatively strong. This reason that makes green composites can be applied in Unmanned Aerial Vehicle (UAV). In this study, material of quadcopter frame was composites material that made of waste material from styrofoam, bagasse and eggshell. Styrofoam was used as binder of composite material. Bagasse and eggshell was used as reinforcement in green composite material. The investigation focused on effect of volume fraction on flying time of quadcopter that made of green composites material. This study showed that addition of eggshell powder in composites up 25% by volume fraction, result in decreasing the flying time of quadcopter. Addition of eggshell powder in composites up 25% by volume fraction,  result in decreasing the porous of green composite. Porous structure affect the flying time of quadcopter based on green composite materials that made of waste material from styrofoam, bagasse and eggshell. Green composite based on styrofoam, bagasse and eggshell can be applied in Unmanned Aerial Vehicle (UAV) materials.

References

M. Perdana, Prastiawan, and S. Hadi, “IOP Conference Series : Earth and Environmental Science Mechanical Properties of Composite Waste Material Based Styrofoam , Baggase and Eggshell Powder for Application of Drone Frames Mechanical Properties of Composite Waste Material Based Styrofoam , Bag,” in IOP Conf. Series: Earth and Environmental Science 97 (2017) 012034, 2017, pp. 1–7.

M. Perdana, “Pengaruh Beban Dinamik terhadap Kekakuan ( Stiffness ) Komposit Hibrid Berbasis Fiberglass dan Coir,” Tek. Mesin - Inst. Teknol. Padang, vol. 6, no. 1, pp. 1–5, 2016.

F. K. Liew, S. Hamdan, R. Rahman, and M. Rusop, “Thermomechanical Properties of Jute / Bamboo Cellulose Composite and Its Hybrid Composites : The Effects of Treatment and Fiber Loading,” Adv. Mater. Sci. Eng., vol. 2017, pp. 1–10, 2017.

J. Sahari and M. A. Maleque, “Mechanical Properties of Oil Palm Shell Composites,” Int. J. Polym. Sci., vol. 2016, pp. 1–8, 2016.

L. Iryani, A. M. Kadir, and B. Irawan, “Design and Analysis of Spar I Beam Profile Using Composite Material in UAV Structure,” in Annual South East Asian International Seminar (ASAIS) 2017, 2017, pp. 45–50.

M. Barbuta, D. Diaconu, A. A. Serbanoiu, A. Burlacu, A. Timu, and C. M. Gradinaru, “Effect of Tire Waste on The Mechanical Properties of Concrete,” in 10th International Conference Interdisciplinarity in Engineering, 2017, no. August, pp. 346–350.

S. Khairunnisa, “Pengolahan Limbah Styrofoam Menjadi Produk Fashion,” in e-Proceeding of Art & Design, 2016, vol. 3, no. 2, pp. 253–268.

H. Mamtaz, M. H. Fouladi, M. Al-atabi, and S. N. Namasivayam, “Acoustic Absorption of Natural Fiber Composites,” J. Eng., vol. 2016, pp. 1–11, 2016.

X. Zhang and Y. Han, “Thermal Insulation Properties of Fly Ash and Waste Polystyrene Mixed Block Building Materials,” Chem. Eng. Trans. J., vol. 55, pp. 253–258, 2016.

H. He, J. Nie, and J. Wang, “Flexible Wood Fiber Composite Floor,” Adv. Mater. Sci. Eng., vol. 2015, pp. 1–6, 2015.

S. H. M and B. T. A, “Applications of Green Composites in Immobilization of Radioactive Wastes and Others- A Review,” J. Nucl. Energy Sci. Power Gener. Technol., vol. 6, no. 4, 2017.

L. Guadagno, M. Raimondo, L. Vertuccio, C. Naddeo, G. Barra, P. Longo, P. Lamberti, G. Spinelli, and M. R. Nobile, “Morphological, rheological and electrical properties of composites filled with carbon nanotubes functionalized with 1-pyrenebutyric acid,” Compos. Part B Eng., vol. 147, no. January, pp. 12–21, 2018.

I. O. Oladele, “Effect of Bagasse Fibre Reinforcement on the Mechanical Properties of Polyester Composites,” J. Assoc. Prof. Eng. Trinidad Tobago, vol. 42, no. 1, pp. 12–15, 2014.

S. da L. Maria, S. da C. Maria, A. G. Roberto, A. Pascoal, and S. da C. Aparecida, “Polypropylene Composites Reinforced with Biodegraded Sugarcane Bagasse Fibers : Static and Dynamic Mechanical Properties,” Mater. Res., vol. 19, no. 1, pp. 75–83, 2015.

A. S. Yusuff, O. D. Adeniyi, M. A. Olutoye, and U. G. Akpan, “Development and Characterization of A Composite Anthill-Chiken Eggshell Catalyst For Biodiesel Production From Waste Frying Oil,” Int. J. Technol., vol. 9, no. 1, pp. 110–119, 2018.

N. Tangboriboon, P. Selarak, P. Shamunee, and A. Sirivat, “Innovative Green Bio-Filler and Bio-Flux Calcium Carbonate from Eggshells to Hard-Soft Porcelain Preparation,” Chem. Technol. An Indian J., vol. 11, no. 6, pp. 1–10, 2016.

A. Balachandran, D. Karelia, and J. Challa, “Material Selection for Unmanned Aerial Vehicle,” Int. J. Mech. Enginering Technol., vol. 5, no. 8, pp. 34–40, 2014.

A. M, G. Diwakar, and R. Ratukam, “Design of A Quad Copter and Fabrication,” Int. J. Innov. Eng. Technol. Des., vol. 4, no. 1, pp. 59–65, 2014.

N. Ives, R. Pacheco, D. De Castro, R. Resende, and A. A. Magalhães, “Stability Control of an Autonomous Quadcopter through PID Control Law,” Int. J. Eng. Res. Appl., vol. 5, no. 5, pp. 7–10, 2015.

S. Sayuti and M. H. Soffan, “Perancangan dan Pembuatan Rangka Drone yang Ekonomis dan Praktis,” in Prosiding Seminar Nasional Aplikasi Sains & Teknologi (SNAST), 2016, pp. 485–490.

Published

2018-10-31

How to Cite

Perdana, M., Nurzal, Firdaus, S., & Saferi, R. (2018). Flying Time Of Quadcopter Based On Green Composites Material. Jurnal Teknik Mesin, 8(2), 73–77. https://doi.org/10.21063/jtm.2018.v8.i2.73-77